Sidas Heat Race S.E.T. Sock Powered By Therm-ic PowerSock S-Pack 700 Bluetooth

Thin, precise ski socks designed for athletes in extreme conditions.

Their thin construction, combined with Smart.Elastic. technology, allows for an unaltered fit in the boots for maximum comfort and feel. The thin (2mm) S.E.T heating line is discreetly integrated into the sock to diffuse subtle warmth around the toes, without impacting on the fit of the sock in the shoe. In addition, the polyamide fibres, which provide tension around the foot and leg, ensure that the sock fits snugly and supports the foot during exercise.

Made from merino wool, these socks offer excellent insulation and moisture management. Merino wool regulates temperature and humidity, is breathable and insulating. It is able to absorb up to 33% of its own weight in moisture before it appears wet. This fibre therefore keeps your skin dry and warm. It acts as an insulating layer offering optimal thermal insulation.

Thin heating element: The thin (2mm) S.E.T heating line is discreetly integrated into the sock to diffuse subtle warmth around the toes without impacting the fit of the sock in the shoe.

Precision: 3 factors ensure the precision of the socks in skiing: sock knitting, thickness and tension. These socks are knitted with 200 needles and are fully engineered with an inside-out construction (no yarn cut into the socks), one of the highest definitions available for socks, the tension is strong but inclusive to keep the sock around the feet and legs and the thickness is low to improve contact with the ski boot.

Warmth: Thanks to the merino wool, the socks provide warmth and wick away moisture.

With the S-Pack 700 Bluetooth battery, you can control your heat remotely using your smartphone.

First Use And Charging Of The S-Pack Battery:

Important note:

• The S-Pack battery must be charged before using them for the first time.
• Preparing the USB wall plug universal charger (optional).
• Slide your country-specific adapter into the slot on the back of the charger until it locks in with an audible click.

USB cable charging process:

1. Plug the USB cable into the USB port. The charge indicator (2.2) will light up green. Next, you plug the charging connectors of the cable into the batteries S-pack (2.4). Please check the illustration on the charger to ensure proper orientation. The S-Pack battery can be charged in any operating mode. The charging process will start automatically and the charge indicator (2.2) will light up in red during charging.

2. Once the S-Pack batteries are fully charged, the charging process is automatically concluded and the LED on the charge indicator (2.2) will switch back to green.

3. LED blinking on USB S-Pack charger between green and red when charge above 95%. LED stays green when fully charged.

4. Remove both S-Pack batteries from the charging shaft.

5. After the S-Pack batteries have been charged, they are automatically in POWER OFF mode.

Important note:

Recharge the S-Pack battery after each use. This extends the service life of the batteries and ensures that the device is always ready for use.
The battery consists of lithium ion cells and can be charged in any state. For this reason, the battery does not need to be fully discharged before charging.
When starting the charging process, the S-Pack battery can be in any operating mode (Power Off, In Use)
The full charging capacity of the S-Pack battery can only be conserved if the S-Pack battery are removed from the charging station after the charging procedure is complete.

How To Use The Powersock Battery

Wear the heatable sock.
Push the S-Pack battery on to the snap fasteners until they audibly lock into place (3.2).
The S-Pack battery can be controlled with button (1.3) or with a iOS and Android app (only for S-Pack Bluetooth enabled).

Important Instructions For Use:

Do not allow the highest heat level to be switched on for more than a few minutes at a time. This could produce too much heat during operation, which may cause burns.
Always set S-Pack battery to low or moderate heat levels to maintain comfortable foot warming (heating should be almost undetectable).
The optimum heat output is only reached when the socks, boots or soles are dry.
Never used the heatable sock and the heatable insole together; this can result in too much heat – risk of burning!

Information about Therm-IC S-Pack Battery Styles:

S-Pack without bluetooth The S-Pack battery has 4 operating modes: Power Off – In Use Levels . They are indicated with the heating level display on the S-Pack battery. The LED flashing modes corresponds to the selected heat setting.

S-Pack with bluetooth Using the phone App: Please refer to the Bluetooth app or www.therm-ic.com.

Turning the device on: Press the control button (1.3) for a long period of time (approx. 3 sec) to turn on the S-Pack battery at the lowest heat level. If the control button is pressed for too long (approx. more than 6s), the S-Pack will remain in OFF mode.

Features:

• Made from merino wool, these socks offer excellent insulation and moisture management.
• Thin heating element
• Thin, precise ski socks designed for athletes in extreme conditions.
• Low Volume
• Composition: 60% Merino wool 36% Polyamide 4% Elastane

Battery Features:

• Bluetooth function
• Warm feet for up to 8 hours
• Pack comes with a USB charger
• Wall charger not supplied S-Pack batteries are suitable for use with the Therm-ic PowerSocks heated socks

Specifications:

• Season: Fall / Winter
• Category: Socks
• 7 Sizes : 35-36 / 37-38 / 39-40 / 40-41 / 42-43 / 44-46 / 47-49
• Unisex
• Color : Grey / Yellow